美国VTI手套箱微量水分析仪探头MK-XTR-100使用注意事项
注意：用于刷新湿度传感器功能的磷酸溶液具有腐蚀性。请戴防护手套和护目镜。
1从手套箱中卸下水分分析仪之前，请断开系统电缆
2从湿度探头上拧下护罩（防护罩）盖。
三。在传感器探头上涂抹蒸馏水。用无绒布擦干（不要用纸巾）。小心操作探头。避免过度接触探头表面。美国VTI手套箱微量水分析仪探头MK-XTR-100使用注意事项
4在旋转装置的同时，将10到15滴磷酸溶液直接滴在探头上，使传感器湿润。将足够的溶液滴到探头上，直到表面完全覆盖。
让传感器风干四小时。在探针下方放置一块滴布，以收集多余的酸。
（©）真空技术公司，美国马萨诸塞州格洛斯特市大共和国大道15号，邮编：01930，2016年
5完全干燥后，更换探头上的保护罩。
6在拆下法兰盖并更换端口中的传感器之前，确认手套箱仍在+5 mBar到+8 mBar的压力范围内。
7将水分分析仪重新安装到手套箱后，重新连接系统电缆。美国VTI手套箱微量水分析仪探头MK-XTR-100使用注意事项
8在触摸屏上，触按“Analyzer”以激活水分分析仪。
9记录湿度数据
注：在锂电池和有机金属应用中，操作过程中挥发的酸/碱会腐蚀湿度传感器，从而导致电阻变化。显示的湿度值可能与实际湿度值不同。偏差程度取决于腐蚀性物质的浓度以及传感器刷新过程的彻底性。在这种情况下，我们建议在保修期内将分析仪发送给我们进行免费校准。
Maintenance of the Moisture Analyzer
Attention: The phosphoric acid solution used for refreshing the functionality of the moisture sensor is corrosive. Please wear protective gloves and eyewear.
-
Disconnect the system cable before removing the moisture analyzer from the glove box
-
Unscrew the shroud (protective cage) cover from the moisture probe.
-
Apply distilled water on the sensor probe. Dry with a lint-free cloth (do not use paper towels). Handle the probe with care. Avoid excessive contact the surface of the probe.美国VTI手套箱微量水分析仪探头MK-XTR-100使用注意事项
-
Moisten the sensor with the phosphoric acid solution by slowly dripping 10 to 15 drops directly on the probe while rotating the unit. Drip enough of the solution onto the probe until the surface is completely covered.
Allow the sensor to air-dry for four hours. Place a drop cloth under the probe to catch excess acid.
(©)Vacuum Technology Inc., 15 Great Republic Drive, Gloucester, MA, 01930 USA 2016
-
When completely dry, replace the protective shroud on the probe.
-
Confirm that the glove box is still within the pressure range of +5 mBar to +8 mBar before removing the blind flange cover and replacing the sensor in the port.
-
Reconnect the system cable after the moisture analyzer is reinstalled in the glove box.
-
On the touchscreen, touch “Analyzer” to activate the moisture analyzer.
-
Log the moisture data
Note: In lithium battery and in organometallic applications, volatilized acid/alkali during operation will corrode the moisture sensor which can cause a change in electrical resistance. The displayed moisture value might be different from the actual moisture value. The degree of deviation depends on the concentration of corrosive substances as well as the thoroughness of the sensor-refreshing process. In this case, we recommend sending the analyzer to us for a free calibration within the warranty period.
更多美国VTI手套箱微量水分析仪探头MK-XTR-100使用注意事项信息请直接致电埃登威上海021-55581219产品：微量氧分析仪,药品残氧仪,露点仪,热导气体分析仪,GE流量计,OX-1氧传感器,顶空分析仪,红外气体分析仪,高温湿度仪,西门子U23分析仪,ppb微量水分析仪,OXY.IQ氧分析仪,烟气湿度仪,燃气热值仪,Kaye温度验证仪,L&W白度,仪激光氧分析仪,压缩空气露点仪,干燥机露点仪,激光气体分析仪,便携式露点仪,便携式微量氧分析仪，Fei （维修中心，代表处，总代理，分公司，子公司，售后中心，销售中心，上海办，办事处在哪里）
